09:22

Prepare bill of material for a 1KW solar photovoltaic installation | NIMI | DIGITAL | HINDI |

09:44

Estimate cost of a 1 KW solar PV installation and prepare a quotation | NIMI | DIGITAL | HINDI |

10:08

Making samples of different pockets PART - 1 | NIMI | DIGITAL | HINDI |

10:23

Making samples of different pockets PART - 2 | NIMI | DIGITAL | HINDI |

10:48

Straight saw on thick section of MS angle and pipes | NIMI | DIGITAL | HINDI |

11:51

File radius along a marked line (convex and concave) and match | NIMI | DIGITAL | HINDI |

08:43

Measure slip and power factor to draw slip Vs torque characteristics | NIMI | DIGITAL | HINDI |

09:11

Test for continuity and insulation resistance of 3 phase induction motor | NIMI | DIGITAL | HINDI |

11:39

Connect start, run three phase induction motor by using DOL starters | NIMI | DIGITAL | HINDI |

10:08

Determine efficiency of 3 phase squirrel cage induction motor by no-load | NIMI | DIGITAL | HINDI |

08:15

Determine the efficiency of squirrel cage induction motor by brake test | NIMI | DIGITAL | HINDI |

10:35

Pipe butt joint on aluminum pipe 50mm * 3mm WT in flat position GTAW | NIMI | DIGITAL | HINDI |

10:13

Fillet weld - outside corner joint on aluminum sheet 2mm thick GTAW | NIMI | DIGITAL | HINDI |

12:34

Safety signs for danger, warning, caution & personal safety message | NIMI | DIGITAL | HINDI |

16:38

First aid method and basic training | NIMI | DIGITAL | HINDI |

09:40

Use of tools and equipment | NIMI | DIGITAL | HINDI |

08:59

Record filling, draping and using tools for shaping nails | NIMI | DIGITAL | HINDI |

12:56

Construct and test 4 to 1 multiplexer | NIMI | DIGITAL | HINDI |

10:22

Construct and test 1 to 4 De - multiplexer | NIMI | DIGITAL | HINDI |

13:00

Familiarize with different types of condensers used in refrigerators | NIMI | DIGITAL | HINDI |

15:00

Clean, service and leak test different types of air - cooled condensers | NIMI | DIGITAL | HINDI |

08:25

Connect start, run and reverse direction of rotation of slip-ring motor | NIMI | DIGITAL | HINDI |

08:48

Client consultation and handling Part -B | NIMI | DIGITAL | HINDI |

07:06

Client consultation and handling Part - A | NIMI | DIGITAL | HINDI |

09:51

Make a connection of automatic star - delta starter with 3 contractors | NIMI | DIGITAL | HINDI |

09:21

Identification of advanced logic gate ICs | NIMI | DIGITAL | HINDI |

09:24

Identification of basic logic gate ICs | NIMI | DIGITAL | HINDI |

17:17

Importance of trade training, list of tools & machinery used in trade | NIMI | DIGITAL | HINDI |

14:31

Safety attitude development of trainee by educating them to use PPE | NIMI | DIGITAL | HINDI |

08:40

Check control circuit of variable speed air conditioners (INVERTER ACs) | NIMI | DIGITAL | HINDI |

12:34

Check and test different types of relays, capacitors finding faults | NIMI | DIGITAL | HINDI |

07:26

Perform testing battery with hydrometer | NIMI | DIGITAL | HINDI |

07:05

Tracing of hydraulic circuit on hydraulic jack, brake circuit part - 2 | NIMI | DIGITAL | HINDI |

09:01

Prepare simple electrical circuits, measure current using multimeter | NIMI | DIGITAL | HINDI |

05:39

Tracing of hydraulic circuit on hydraulic jack, brake circuit part - 1 | NIMI | DIGITAL | HINDI |

06:37

Addie | NIMI | DIGITAL | HINDI |

09:13

Course construction and syllabus analysis | NIMI | DIGITAL | HINDI |

09:48

Lesson plan preparation - 2 | NIMI | DIGITAL | HINDI |

07:01

Skill learning | NIMI | DIGITAL | HINDI |

05:00

Phases of Skill Learning | NIMI | DIGITAL | HINDI |

10:51

Demonstration plan | NIMI | DIGITAL | HINDI |

08:08

Lesson plan preparation | NIMI | DIGITAL | HINDI |

08:17

Demonstrate different types of saws -ripping cross cutting and obtique | NIMI | DIGITAL | HINDI |

06:18

Demonstrate the use of bench vice,bench hook bench stop and also their | NIMI | DIGITAL | HINDI |

05:37

Use and practice of portable power circular saw | NIMI | DIGITAL | HINDI |

06:59

Demonstrate the use of country dril ,hand drill ratchet brace drill | NIMI | DIGITAL | HINDI |

05:00

Sharpening and setting of saw blade| NIMI | DIGITAL | HINDI |

09:47

Demonstrate different types of saws Ripping cross cutting curve cutting | NIMI | DIGITAL | HINDI |

09:51

Prepare the installation material for a reciprocating pump | NIMI | DIGITAL | HINDI |

08:42

Demonstrate working of solar water heating system | NIMI | DIGITAL | HINDI |

09:59

Assemble GI pipes with standard fittings | NIMI | DIGITAL | HINDI |

10:00

Fit the water meter and demonstrate delivery of water to overhead tank | NIMI | DIGITAL | HINDI |

09:41

Administer first aid and use a fire extinguisher | NIMI | DIGITAL | HINDI |

09:01

Tools And ITS APPLICATION | NIMI | DIGITAL | HINDI |

11:53

Thread on Ms Flat & pipe ,Locking Device | NIMI | DIGITAL | HINDI |

10:29

Cut various types of pipes | NIMI | DIGITAL | HINDI |

09:21

Various pipe Fittings and assemblies | NIMI | DIGITAL | HINDI |

09:31

Safety standards , protocols and first aid | NIMI | DIGITAL | HINDI |

08:41

Pipe bending techniques | NIMI | DIGITAL | HINDI |

09:48

Practice using various hand tools | NIMI | DIGITAL | HINDI |