11:22

Gagawa ng Internal spline 12Teeth Pitch 20 na pantanggal ng Gas Valve ng Pryce Gas.

11:49

Handheld Tractor drive pulley for Agriculture rebore to fit engine drive shaft.

14:24

Magrebore ng block ng motor Rusi Neptune 125 oversize ng o.25mm, 52.25 to52.5mmm.

14:17

Mag-Abuno ng mga bungi -bungi na pinion gear ng one bagger cement mixer.

09:26

Kunya ng double row pulley 3/8×3/16 gamit ang shaper at dividing head.

10:59

Mag-búild-up at rebore ng I-beam ng Ten Wheeler na Truck.

13:50

Tamang teknik sapag Thread ng shafting 3/4NC10 stainless na gamit pandagat.

11:39

mag-Taper ng Polya para Compressor na inimbudo ang drive shaft

12:06

Gagawing double bearing ang hub ng motor para matatag pagdating sa kargahan.

13:32

Kung kaya bang barenahan at saka Turnohin Ang Mulle or Leaf Spring.

08:47

Ang tamang paraan ng pag thread ng tubo 11/2 to fit elbow ng hindi masisira.

10:34

Ang madaling paraan sa pag-ayos ng basag na bearing seat sa hub ng motor.

10:16

Ating Turnohin at alamin kung gaano katigas ang Pin ng Backhoe.

11:25

Mag resurface ng head Toyota vios 1.2 manual dahil bengkong sanhi ng overheat.

11:14

Simpleng paraan ng pag thread ng shafting sa Turno (Tutorial)para sa mga beginners.

20:52

Reduction of Gear Pump Spline teeth drive shaft from 14Teeth to 10teeth Pitch 12.

23:43

Simpleng Paraan ng Paggawa ng isang Homemade power Hacksaw(do it yourself)

18:35

Paano mag-build-up ng Loose bearing seat ng rotor disc bearing hub ng di tumitigas ang welding.

07:49

Paano magbuild-up ng cast iron material ng hindi tumitigas o machinable pa rin.

08:22

Paano mag -repair ng pod-pod na pinion gear ng One bagger cement mixer.

09:08

Cylinder head skimming or warping due to overheat or was subject to extreme temp.

17:13

Paano magrebore ng Four cylinders na block Ng Mitsubishi 4D32 at maglagay ng Liner,double rebore.

14:01

Build-up and machining of internal gear 18teeth Pitch 12.

15:47

Gagawa tayo ng internal Gear14 teeth Pitch12 to fit Gear Pump.

19:34

Build-up and milling of spur gear 18T-P10 in vertical milling machine.

13:54

Build-up and machining of internal gear 18Teeth Pitch10.

14:26

Build-up of three rows Sprocket precisely using grinder.

10:27

Paano magtanggal ng mga putol na Piso baso sa cylinder head de Cam Lobe

11:48

magaayos ng nabangga na motor dahil lasing Rusi surf125cc..

12:44

paano gumawa ng bareta gamit sa pagtatatanim ng saging

12:03

Magreface or mag skimmed ng Multicab Cylinder head dahil nag overheat .

14:38

Sprocket Gear drive of mud boat build -up machining to fit Bearing.

14:44

Propeller Spline Shaft 16T-P10,nasira, build -up,machining and re -milling.

12:30

Mag Thread ng Shafting 1/2× 13TPI

12:17

Magreface ng Breakdrum at magpantay ng surface.

10:05

Magpalit ng cross bearing assembly sa propeller shaft due to damage

17:20

Mag rebore ng Front Axle bearing Hub dahil mahaba ang nabiling bearing.

17:30

Gagawa ng ROPE PULLEY

06:34

Gagawa ng Stud Bolt ng Tractor.

24:05

Engine Block Liners 4pcs. Press in and press out 4D32.

17:07

Rebushing of 2pcs.hydraulic Cap front and back of Hydraulic Cylinder using Tiger bronze.

08:40

magtanggal ng Polya or Pulley na naka kabit sa makina dahil kinalawang at may welding.

17:00

Magaayos ng sirang Turno or Lathe Machine.

08:36

Build-up and Re-thread Router rotor Spindle to fit nut.

16:58

Mag -Reface ng Flywheel ng Dumptruck 10PC,dahil sa Slide at saka Dragging.

13:03

Gagawa ng Worm Gear 40T-P10 para sa Gear Box ng Drilling Machine.

11:12

Ang Pagbisita ko sa Palo,Leyte sa MacArthur Landing Memorial National Park.

18:50

Telescopic Fork na may GasGas Paano Baliktarin.

10:05

Dragging ba ang Scooter mo,ito ang solusyon,Clutch Bell Re-Groove.

12:19

Crankshaft ng Chainsaw na putol pagpalitin kasama alignment.

16:06

Gagawa ng internal gear 10T- P14 to Fit Gear Pump Drive.

14:02

Paano Gagawin ang Inside K-WAY sa Drill Press.

09:36

Bearing Hub Loose, Build-up, Machining and Press Fitting.

09:32

Canigao Island,The Island of Paradise,The Boracay of Eastern Visayas, Matalom, Leyte, Philippines.

06:04

Canigao Island, The Island of Paradise/The Boracay of Eastern Visayas,Matalom, Leyte Philippines

11:38

Canigao,The Island of Paradise,Matalom, Leyte, Philippines, How to get there.

06:01

Canigao Island,The Boracay of Eastern Visayas,Matalom, Leyte Philippines.

12:31

Connecting Rod and Side Bearings Replacement Dismantle and assemble and re -alignment.

02:22

Itik at Pabo Showdown

12:38

Telescopic fork may Gasgas,at Tagas,babaliktarin gamit ang Turno.