I got a puss invasion :( i tried to block the fence between me and my neighbor ... but... she likes to be here, she was sleeping in my bed when i wanted to sleep yesterday (scared the shit out of me i did not expected a cat) now she is just sitting here , i dont feed her! , i hope it wont cause problems with my new puss. the tiny one is super sweet, but not my cat..... rather not have her in my bed... entering sneaky in my kitchen
14 - 4
This weekend i am going to visit hopefully a new friend ! a new puss wondering around and destroying my projects in my videos. she is an older puss of 10 years, exactly what i was looking for ! people ask why so old ? well in short, i think its a shame they end up in asylums. sometimes because people are done with them (Cleo was disposed of since it did not fit in there way of living, and she had bladder problems) .... (Stinky was dumped because the woman in question wanted to immigrate ) and in this case the person became sick and could not care for her anymore (not his fault). a good reason to make her last years a few good ones i hope.
And most people will take the little kitten and yes they are sweet. but dont forget these older ones!!! its not a piece of electronics!!. i cant wait, hopefully soon in videos :)
26 - 7
First test frame... no use for it but im new to drawing and printing :) wanted to know what a mid/tweeter frame would take to print and how it looks and if it fits... fits perfectly , printed on sporty.....speed setting. took around 45 minutes. i now adjusted the frame since it did not have to be so thick. on sporty it takes 33min and on ludicrous..... 166% 24 minutes lets see how that looks at this speed. i tried some TPU and thats a complete disaster ! it sucks ! PLA, no problems and i guess, my favourite so far !
16 - 0
Thats why i hate push pull magnet structure :) you only have to forget the pins to hold everything in place while disassembling, and you can reglue a bunch of magnets ;)
14 - 4
Well with this Neje 4640 laser you can cut trough alu foil if you really really want... must have a coat of black though. this is 7 micron aluminium with black paint it cuts trough it at 200 out of 255 power at 2000mm/minute usefull ? i dont think so because it will become a mess. but it surprises me it actually can with some help of paint. obviously this is the back side (no paint)
12 - 9
its a bit older, but i forgot it was there, a presentation on the ZBA Diy Audio event about my speakers in 2023 (the one i made the week before the event), its like 1/8th of what i told. well since you know i can talk for hours so.... i think they cut it short haha
it might be interested to see the whole video , but remember its in dutch so.
the speakers from Chris pirate logic prototype on the table also uses the same mid range tweeter i made.
https://youtu.be/u63ok0V2ftg?t=513
watch video on watch page
4 - 0
Well i wanted to measure the working driver today, i made a test baffle, and thought measure the driver one more time ... then i thought...... wait a minute in parallel i get 13 ohm that should be halve that... so also this driver has one broken lead..... so unfortunately no measurements :(
10 - 2
Chris from Pirate Logic, talking about his MFB project using one of my drivers :)
https://www.youtube.com/watch?v=focW7...
watch video on watch page
12 - 0
Reserved !
34 - 2
OOh i stopped recording the modding of the Z axis. it was waaaaaaaay to slow. but this is how it looks after its done :)
4 - 2
HI , i am doing some diy loudspeaker contraptions.from esl, rubanoides, planar magnetic speakers and or headphones to amt and alike :) i enjoy building on the cheap, so i hope you do to :)