09:18

Prepare bill of material for a 1KW solar photovoltaic installation | NIMI | DIGITAL | TAMIL |

09:38

Estimate cost of a 1 KW solar PV installation and prepare a quotation | NIMI | DIGITAL | TAMIL |

10:18

Making samples of different pockets PART - 2 | NIMI | DIGITAL | TAMIL |

10:14

Making samples of different pockets PART - 1 | NIMI | DIGITAL | TAMIL |

11:47

File radius along a marked line (convex and concave) and match | NIMI | DIGITAL | TAMIL |

10:46

Straight saw on thick section of MS angle and pipes | NIMI | DIGITAL | TAMIL |

11:35

Connect start, run three phase induction motor by using DOL starters | NIMI | DIGITAL | TAMIL |

08:18

Determine the efficiency of squirrel cage induction motor by brake test | NIMI | DIGITAL | TAMIL |

09:10

Test for continuity and insulation resistance of 3 phase induction motor | NIMI | DIGITAL | TAMIL |

10:11

Determine efficiency of 3 phase squirrel cage induction motor by no-load | NIMI | DIGITAL | TAMIL |

08:45

Measure slip and power factor to draw slip Vs torque characteristics | NIMI | DIGITAL | TAMIL |

10:37

Pipe butt joint on aluminum pipe 50mm * 3mm WT in flat position GTAW | NIMI | DIGITAL | TAMIL |

10:02

Fillet weld - outside corner joint on aluminum sheet 2mm thick GTAW | NIMI | DIGITAL | TAMIL |

16:34

First aid method and basic training | NIMI | DIGITAL | TAMIL |

12:34

Safety signs for danger, warning, caution & personal safety message | NIMI | DIGITAL | TAMIL |

10:45

Use of tools and equipment | NIMI | DIGITAL | TAMIL |

10:17

Record filling, draping and using tools for shaping nails | NIMI | DIGITAL | TAMIL |

10:33

Construct and test 1 to 4 De - multiplexer | NIMI | DIGITAL | TAMIL |

12:58

Construct and test 4 to 1 multiplexer | NIMI | DIGITAL | TAMIL |

14:53

Clean, service and leak test different types of air - cooled condensers | NIMI | DIGITAL | TAMIL |

12:47

Familiarize with different types of condensers used in refrigerators | NIMI | DIGITAL | TAMIL |

09:53

Make a connection of automatic star - delta starter with 3 contractors | NIMI | DIGITAL | TAMIL |

09:43

Client consultation and handling | NIMI | DIGITAL | TAMIL |

07:58

Client consultation and handling | NIMI | DIGITAL | TAMIL |

08:29

Connect start, run and reverse direction of rotation of slip-ring motor | NIMI | DIGITAL | TAMIL |

09:28

Identification of advanced logic gate ICs | NIMI | DIGITAL | TAMIL |

09:26

Identification of basic logic gate ICs | NIMI | DIGITAL | TAMIL |

13:56

Safety attitude development of trainee by educating them to use PPE | NIMI | DIGITAL | TAMIL |

17:22

Importance of trade training, list of tools & machinery used in trade | NIMI | DIGITAL | TAMIL |

12:47

Check and test different types of relays, capacitors finding faults | NIMI | DIGITAL | TAMIL |

08:29

Check control circuit of variable speed air conditioners (INVERTER ACs) | NIMI | DIGITAL | TAMIL |

08:25

Tracing of hydraulic circuit on hydraulic jack, brake circuit part - 2 | NIMI | DIGITAL | TAMIL |

08:07

Perform testing battery with hydrometer | NIMI | DIGITAL | TAMIL |

10:36

Prepare simple electrical circuits, measure current using multimeter | NIMI | DIGITAL | TAMIL |

06:04

Tracing of hydraulic circuit on hydraulic jack, brake circuit part - 1 | NIMI | DIGITAL | TAMIL |

05:01

Phases of Skill Learning | NIMI | DIGITAL | TAMIL |

10:46

Demonstration plan | NIMI | DIGITAL | TAMIL |

09:49

Lesson plan preparation - 2 | NIMI | DIGITAL | TAMIL |

08:09

Lesson plan preparation | NIMI | DIGITAL | TAMIL |

09:12

Course construction and syllabus analysis | NIMI | DIGITAL | TAMIL |

07:03

Skill learning | NIMI | DIGITAL | TAMIL |

06:39

Addie | NIMI | DIGITAL | TAMIL |

07:01

Demonstrate the use of country drill ,hand drill ratchet brace drill | NIMI | DIGITAL | TAMIL |

06:16

Demonstrate the use of bench vice bench hook bench stop and also their | NIMI | DIGITAL | TAMIL |

09:45

Demonstrate different types of saws Ripping cross cutting curve cutting | NIMI | DIGITAL | TAMIL |

08:12

Demonstrate different types of saws Ripping cross cutting curve cutting | NIMI | DIGITAL | TAMIL |

05:46

Use and practice of portable power circular saw | NIMI | DIGITAL | TAMIL |

05:01

Sharpening and setting of saw blade | NIMI | DIGITAL | TAMIL |

09:53

Cut various types of pipes | NIMI | DIGITAL | TAMIL |

11:54

Thread on Ms Flat & pipe ,Locking Device | NIMI | DIGITAL | TAMIL |

09:43

Administer first aid and use a fire extinguisher | NIMI | DIGITAL | TAMIL |

09:19

Various pipe Fittings and assemblies | NIMI | DIGITAL | TAMIL |

09:00

Tools And ITI Application | NIMI | DIGITAL | TAMIL |

09:54

Safety standards , protocols and first aid | NIMI | DIGITAL | TAMIL |

09:57

Fit the water meter and demonstrate delivery of water to overhead tank | NIMI | DIGITAL | TAMIL |

09:29

Demonstrate working of solar water heating system | NIMI | DIGITAL | TAMIL |

09:59

Prepare the installation material for a reciprocating pump | NIMI | DIGITAL | TAMIL |

09:58

Assemble GI pipes with standard fittings | NIMI | DIGITAL | TAMIL |

09:46

Practice using various hand tools | NIMI | DIGITAL | TAMIL |

08:38

Pipe bending techniques | NIMI | DIGITAL | TAMIL |