10:52

Prepare plate earthing and measure earth resistance by earth tester | NIMI | DIGITAL | ENGLISH |

07:59

Practice on measuring instrument in single and three phase circuit|NIMI| DIGITAL|ENGLISH|

06:04

Prepare decorative lamp circuit to produce rotating light Effect | NIMI | DIGITAL | ENGLISH |

07:05

Install light fitting with reflectors for direct and indirect lighting | NIMI | DIGITAL | ENGLISH |

10:25

Perform routine check of machine and do replenish as per requirement | NIMI | DIGITAL | ENGLISH |

13:41

Practice installation of various lamps | NIMI | DIGITAL | ENGLISH |

06:51

Install Light fitting for showcase lighting | NIMI | DIGITAL | ENGLISH |

11:03

Dismantling ,assembling different types of Bearing and check - Part- 2 | NIMI | DIGITAL | ENGLISH

10:02

Group different wattage of lamps in series for specified voltage | NIMI | DIGITAL | ENGLISH |

06:51

Install a solar Panel to charge a rechargeable 12 V DC Battery | NIMI | DIGITAL | ENGLISH |

09:46

Dismantling ,overhauling & Assembling cross ,hand slide of lathe carriage | NIMI | DIGITAL| ENGLISH

09:15

Dismantling ,assembling different types of Bearing check - Part-1| NIMI | DIGITAL | ENGLISH |

12:31

Practice on various cutting tools | NIMI | DIGITAL | ENGLISH |

10:02

perform marking using all marking aids| NIMI | DIGITAL | ENGLISH |

08:32

Practice on fire extinguishers| NIMI | DIGITAL | ENGLISH |

08:52

practice on marking and drilling clear and blind holes part 2 | NIMI | DIGITAL | ENGLISH |

07:07

Perform Practice on hacksawing and filing to given dimensions| NIMI | DIGITAL | ENGLISH |

07:31

practice on marking and drilling clear and blind holes part 1 | NIMI | DIGITAL | ENGLISH |

07:41

Practice to remove wheel lug nuts with use of an air impact wrench | NIMI | DIGITAL | ENGLISH |

11:52

Use transistor as an electronic switch and series voltage regulator| NIMI | DIGITAL | ENGLISH |

10:08

Construct simple circuits containing UJT for triggering and FET amplifier | NIMI | DIGITAL ENGLISH

10:27

Demonstrate different charger specifications |NIMI|DIGITAL|ENGLISH|

10:05

Practice on repair and maintenance of circuit breaker | NIMI | DIGITAL | ENGLISH |

09:02

check transistors their functioning by identifying its type terminals | NIMI | DIGITAL | ENGLISH

10:56

Bias the Transistor and Determine its Characteristics | NIMI | DIGITAL | ENGLISH |

07:17

Test tripping characteristic of circuit breaker for over current |NIMI|DIGITAL| ENGLISH|

07:06

Practice setting of pick up current and time setting multiplier for relay|NIMI| DIGITAL|ENGLISH |

12:10

construct Half , full wave bridge rectifiers using semiconductor diode | NIMI | DIGITAL ENGLISH |

12:36

Test Active and Passive | NIMI | DIGITAL | ENGLISH |

09:14

Identify various parts of relay and ascertain the operation | NIMI | DIGITAL | ENGLISH |

09:42

Identify the parts of circuit breaker, check its operation | NIMI | DIGITAL | ENGLISH |

09:51

Practice of Different types of cuts - Part -1 | NIMI | DIGITAL | ENGLISH |

11:13

Check starter and charging circuit of a vehicle -Part -1 | NIMI | DIGITAL | ENGLISH |

09:22

Check starter and charging circuit of a vehicle -Part -2 | NIMI | DIGITAL | ENGLISH |

10:59

Overhauling distributor | NIMI | DIGITAL | ENGLISH |

06:50

Service turbocharger | NIMI | DIGITAL | ENGLISH |

08:36

Selection of cosmetics and implementation| NIMI | DIGITAL | ENGLISH |

06:10

Overselling carburettor fuel system | NIMI | DIGITAL | ENGLISH |

09:20

Practice of Different types of cuts - Part -2 | NIMI | DIGITAL | ENGLISH |

07:41

Test engine vacuum and compression | NIMI | DIGITAL | ENGLISH |

09:46

Trouble tracing the engine through the dashboard gauge. | NIMI | DIGITAL | ENGLISH |

09:37

Practice in CTM Procedure | NIMI | DIGITAL | ENGLISH |

08:36

Refitting cylinder head| NIMI | DIGITAL | ENGLISH |

09:15

Measuring cylinder bore for taper and ovality - Part -2 | NIMI | DIGITAL | ENGLISH |

05:29

Measuring cylinder bore for taper and ovality - Part -1 | NIMI | DIGITAL | ENGLISH |

10:01

Client Drape & skin Analysis | NIMI | DIGITAL | ENGLISH |

04:49

Reassemble engine | NIMI | DIGITAL | ENGLISH |

11:52

Adjust valve clearance | NIMI | DIGITAL | ENGLISH |

08:01

Assembling engine block components | NIMI | DIGITAL | ENGLISH |

07:33

Cleaning and testing engine block | NIMI | DIGITAL | ENGLISH |

06:10

Assembling cylinder head | NIMI | DIGITAL | ENGLISH |

09:35

Overhaul piston and connecting rod assembly | NIMI | DIGITAL | ENGLISH |

07:22

Dismantling a cylinder head assembly | NIMI | DIGITAL | ENGLISH |

10:45

Dismantling of the diesel engine of LMV as per procedure | NIMI | DIGITAL | ENGLISH |

09:17

Cleaning and flushing of evaporator and condenser with dry nitrogen | NIMI | DIGITAL | ENGLISH |

09:49

Inspecting cylinder head components | NIMI | DIGITAL | ENGLISH |

04:59

Start an Compressor| NIMI | DIGITAL | ENGLISH |

06:56

Inspecting the valve assembly | NIMI | DIGITAL | ENGLISH |

09:09

Installation of refrigerator | NIMI | DIGITAL | ENGLISH |

06:54

Wiring the circuit of Refrigerator | NIMI | DIGITAL | ENGLISH |