09:18

Prepare bill of material for a 1KW solar photovoltaic installation | NIMI | DIGITAL | MALAYALAM |

09:35

Estimate cost of a 1 KW solar PV installation and prepare a quotation | NIMI | DIGITAL | MALAYALAM |

10:20

Making samples of different pockets PART - 2 | NIMI | DIGITAL | MALAYALAM |

10:01

Making samples of different pockets PART - 1 | NIMI | DIGITAL | MALAYALAM |

10:44

Straight saw on thick section of MS angle and pipes | NIMI | DIGITAL | MALAYALAM |

11:45

File radius along a marked line (convex and concave) and match | NIMI | DIGITAL | MALAYALAM |

08:44

Measure slip and power factor to draw slip Vs torque characteristics | NIMI | DIGITAL | MALAYALAM |

11:25

Connect start, run three phase induction motor by using DOL starters | NIMI | DIGITAL | MALAYALAM |

09:04

Test for continuity and insulation resistance of 3 phase induction motor |NIMI |DIGITAL |MALAYALAM |

10:05

Determine efficiency of 3 phase squirrel cage induction motor by no-load |NIMI |DIGITAL |MALAYALAM|

08:11

Determine the efficiency of squirrel cage induction motor by brake test | NIMI |DIGITAL |MALAYALAM |

09:38

Fillet weld - outside corner joint on aluminum sheet 2mm thick GTAW | NIMI | DIGITAL | MALAYALAM |

09:59

Pipe butt joint on aluminum pipe 50mm * 3mm WT in flat position GTAW | NIMI | DIGITAL | MALAYALAM |

16:36

First aid method and basic training | NIMI | DIGITAL | MALAYALAM |

12:32

Safety signs for danger, warning, caution & personal safety message | NIMI | DIGITAL | MALAYALAM |

09:29

Use of tools and equipment | NIMI | DIGITAL | MALAYALAM |

08:56

Record filling, draping and using tools for shaping nails | NIMI | DIGITAL | MALAYALAM |

12:50

Construct and test 4 to 1 multiplexer | NIMI | DIGITAL | MALAYALAM |

10:21

Construct and test 1 to 4 De - multiplexer | NIMI | DIGITAL | MALAYALAM |

15:03

Clean, service and leak test different types of air - cooled condensers | NIMI |DIGITAL |MALAYALAM |

12:58

Familiarize with different types of condensers used in refrigerators | NIMI | DIGITAL | MALAYALAM |

08:23

Connect start, run and reverse direction of rotation of slip-ring motor | NIMI |DIGITAL | MALAYALAM|

09:27

Client consultation and handling | NIMI | DIGITAL | MALAYALAM |

07:24

Client consultation and handling | NIMI | DIGITAL | MALAYALAM |

09:56

Make a connection of automatic star - delta starter with 3 contractors | NIMI | DIGITAL |MALAYALAM |

09:22

Identification of advanced logic gate ICs | NIMI | DIGITAL | MALAYALAM |

09:27

Identification of basic logic gate ICs | NIMI | DIGITAL | MALAYALAM |

17:21

Importance of trade training, list of tools & machinery used in trade | NIMI | DIGITAL | MALAYALAM |

13:56

Safety attitude development of trainee by educating them to use PPE | NIMI | DIGITAL | MALAYALAM |

08:40

Check control circuit of variable speed air conditioners (INVERTER ACs) | NIMI |DIGITAL |MALAYALAM |

12:59

Check and test different types of relays, capacitors finding faults | NIMI | DIGITAL | MALAYALAM |

05:05

Tracing of hydraulic circuit on hydraulic jack, brake circuit part - 1 | NIMI | DIGITAL |MALAYALAM |

07:05

Perform testing battery with hydrometer | NIMI | DIGITAL | MALAYALAM |

09:34

Prepare simple electrical circuits, measure current using multimeter | NIMI | DIGITAL | MALAYALAM |

07:06

Tracing of hydraulic circuit on hydraulic jack, brake circuit part - 2 | NIMI | DIGITAL |MALAYALAM |

09:39

Lesson plan preparation - 2 | NIMI | DIGITAL | MALAYALAM |

10:39

Demonstration plan | NIMI | DIGITAL | MALAYALAM |

08:58

Course construction and syllabus analysis | NIMI | DIGITAL | MALAYALAM |

04:51

Phases of Skill Learning | NIMI | DIGITAL | MALAYALAM |

07:51

Lesson plan preparation | NIMI | DIGITAL | MALAYALAM |

06:51

Skill learning | NIMI | DIGITAL | MALAYALAM |

06:27

Addie | NIMI | DIGITAL | MALAYALAM |

08:02

Demonstrate different types of saws -ripping cross cutting and obtique| NIMI | DIGITAL | MALAYALAM |

06:52

Demonstrate the use of country dril ,hand drill ratchet brace drill | NIMI | DIGITAL | MALAYALAM |

05:21

Use and practice of portable power circular saw | NIMI | DIGITAL | MALAYALAM |

04:25

Sharpening and setting of saw blade | NIMI | DIGITAL | MALAYALAM |

09:38

Demonstrate different types ofsaws Ripping cross cutting curve cutting| NIMI | DIGITAL | MALAYALAM |

06:06

Demonstrate the use of bench vice,bench hook bench stop and also their| NIMI | DIGITAL | MALAYALAM |

09:25

Cut various types of pipes | NIMI | DIGITAL | MALAYALAM |

08:57

Tools And ITI Application | NIMI | DIGITAL | MALAYALAM |

09:47

Administer first aid and use a fire extinguisher | NIMI | DIGITAL | MALAYALAM |

11:28

Thread on Ms Flat & pipe ,Locking Device | NIMI | DIGITAL | MALAYALAM |

09:29

Safety standards , protocols and first aid | NIMI | DIGITAL | MALAYALAM |

09:03

Various pipe Fittings and assemblies | NIMI | DIGITAL | MALAYALAM |

09:51

Prepare the installation material for a reciprocating pump | NIMI | DIGITAL | MALAYALAM |

09:58

Fit the water meter and demonstrate delivery of water to overhead tank | NIMI | DIGITAL |MALAYALAM |

08:41

Demonstrate working of solar water heating system | NIMI | DIGITAL | MALAYALAM |

09:58

Assemble GI pipes with standard fittings | NIMI | DIGITAL | MALAYALAM |

08:39

Pipe bending techniques | NIMI | DIGITAL | MALAYALAM |

09:47

Practice using various hand tools | NIMI | DIGITAL | MALAYALAM |