Channel Avatar

Ledge approved @UCSXzhc-rPJUNapZhybDOfug@youtube.com

454 subscribers - no pronouns :c

Engineering service Time served apprenticeship in electrical


06:42
Breakdown of a potentiometer how to fault find & install new one along with signal voltage to VFD
05:15
Motor overload what they do and how to set them, motor set on fire due to mpcb being set wrong
06:06
How to check if you have a PNP or NPN sensor if you don’t have your data sheet or no markings
09:20
Encoders different types incremental and absolute, how they work and how to test them.
02:13
Testing a single phase motor with capacitor, insulation resistance test also checking resistant.
07:25
SY Cable how to terminate, make off step by step practical, after finding some shocking termination
07:32
Fnirsi SG-003A signal generator what it does and how to use it
11:28
Variable frequency drive VFD how they work and how to test them
03:46
Latching circuit understanding why we use them and how to wire them up to contacts and relays
05:23
Load cells how they work and how to test them
04:38
Temperature transmitter how it works and how to test it
04:38
Temperature transmitter how they work and how to test them
03:08
Thermocouple how they work and how to test them
07:07
PNP/NPN what they are how they work and how they work in sensors and the wiring of the sensor
05:45
Testing sensors and how ultrasonic sensor work.
07:51
Test equipment of a maintenance engineer fluke 1587 fc, flir thermal clamp meter and more
02:45
Testing a three phase motor and what voltage to use when doing a insulation resistance test (IR)
03:05
Electronic motor brake what they are, how they work and how to test them
02:58
Float switches, how they work and how to test them 
03:04
Break down video on a low level on our RO unit and float switches in they working environment 
03:09
Standstill monitoring safety relay what it does and how it works.
03:04
Break down on a vac pump where coupling sheared off, along with what a coupling is & what it’s for.
02:58
What a potentiometer is, what it does, how it works and how to test them.
02:23
Pilz how the reset modes work what they mean and why you use them.
01:47
Understanding pilz safety relay how they work and how to wire them up using a e-stop
02:36
How to understand pilz safety relay how they work and how to wire a mag switch into the pilz relay.
02:52
Understanding pilz safety relay how the work and how to wire a coded mag safety switch.
02:59
Understanding pilz safety relay how they work and who to wire them to components
03:00
How a three phase heater will be control by two solid state relay and what to watch out for !!
02:40
20 July 2023
02:58
When fault finding always take everything in don't dismiss something until tested#engineering
02:59
Fault finding why three phase heater not reaching set point (how three pole thermostat works)
02:56
Talking through electrifash panel Part.5 and how a transformer, thermal fuse and cartridge heaters
03:00
Fault finding reed switch and pneumatic cylinder
03:00
Talking through electrical panel & drownings Part.4 & how safety relays work
03:00
Talking through electrical panel & drownings Part.3 & how PLC work
01:32
Talking through electrical panel & drownings Part.2 how solid state relays work (SSR)
02:45
Talking through a electrical panel & drains part1. Solid state relay #engineering #electrical
02:38
Reading and fault finding PLC Siemens S7-300
02:12
Testing a single phase motor with capacitor, insulation resistance test also checking resistant.
02:40
Testing a three phase motor by Insulation resistance test and resistance checking the windings
02:22
RTD/PT100 (resistant temperature device & how to test, using fluke 1587fc
01:29
Panel testing tripped three phase vibrator motor, using fluke clamp meter.
01:24
Little tech tip to pick up  metal swarf if your Henry pack up.
01:19
Day in life of a maintenance engineer this time Peugeot Partner has decided to shit it coolant.
01:21
Day in the life of a maintenance engineer, how to on centre dotting
02:27
Day in the life of a maintenance engineer, on this job tracking conveyor belt.
08:40
Maintenance engineer toolbox tour (live in)