https://www.youtube.com/watch?v=l86nJJUgb3Q
MATERIALS-12VOLTS Charger-12 LED Lights-Blingker Relay-Wire-PVC PIPE #howToMakeDiyDiscoLights#makingDiscoLights#makeDIYDiscoLightshttps://youtu.be/pAt8Yh3wMJ4

https://www.youtube.com/watch?v=e5Pk8JgMW1o
Transform your space into a dance party haven with our guide on how to make a Disco Light. This DIY project lets you create your own vibrant and dynamic LED

https://www.instructables.com/LED-Disco-Light-in-a-Jar/
Step 1: Parts. Here is what you need to build the LED Disco Light in a Jar: 1 mason jar, jam jar or anything with a suitably wide neck and a metal cap. 1 switch. 1 4xAA battery holder, in a 2x2 configuration. 1 9V battery snap (mates with the battery holder) 24 RGB fast or slow-change LEDs*.

https://www.instructables.com/HOW-TO-MAKE-DANCING-LEDS/
Step 4: ASSEBLING THE PARTS. First of all arrange all the parts on the PCB according to the schematic.Be carefull for the capacitorsas they may explode if connected in reverse polarity. Then join all the parts .Then just solder them all together. Now just turn off the lights and you are ready to party.

https://www.wikihow.com/Build-Disco-Lights
3. Hang the motor from the ceiling. Choose a location near the middle of the room that has a horizontal surface you can attach the motor too, such as the ceiling. If the motor is powered by a plug, plan the route that the cord will take. Most disco ball motors will mount to the ceiling with screws.

https://www.ehow.com/how_4840878_make-disco-lights.html
Step 1. Create a mirror ball to hang from the ceiling or any high point in your house, such as a staircase railing or balcony. Choose a rubber ball of any size to use as your mirror ball. Glue a plastic hook, such as the kind used to create temporary wall hangings, to the top of the ball. Make sure that the hook and the glue can hold the weight

https://www.youtube.com/watch?v=cRg-B0N1TQo
In This Video I Show You How To Make Dj light at home or homemade disco light |Rotating DJ Lights from Cardboard I hope you like this new Amazing DIY ideahow

https://www.instructables.com/PVC-Pipe-Lighting/
Step 1: Preparing the PVC Pipe. I didn't glue mine, I just used white duct tape to hold the pieces together. If I went back and did this again, I would certainly use the PVC glue to hold them together. I used one roll of duct tape. Cut the pipe to fit your needs.

https://medium.com/@malisa5500/12-steps-to-diy-disco-lights-bff6c80fb17a
DIY Disco Lights Materials. Arduino Uno (or similar microcontroller) Power supply (5V) RGB LED strip (5m) ... Step 10: Check whether the power supply, controller, RGB LED light strips, and USB

https://forum.arduino.cc/t/how-can-i-make-a-disco-light/103298
It doesn't have to be exact. As an example, if your audio is around 10V and the gate current of the SCRs is 5ma then choose R13, R14 and R15 to be 2K each. If we want the cross-over frequencies to be around 500Hz and 5KHz then: C1 and C4 = 1/ (2000 * 500) = 1uF. C2 and C3 = 1/ (2000 * 5000) = 0.1uF. robtillaart May 13, 2012, 7:23pm 5.

https://www.youtube.com/watch?v=vDd6uZbehXY
How to build disco lights at home for your party or if you whant a strobe illusion a flashing lights is now very easy to make.https://www.youtube.com/watch?v

https://www.instructables.com/Simple-DISCO-strobe-light-DIY/
Step 1: Components and Circuit Scheme. The main thing in this little project are white LED lights which I used instead of expensive strobe light because they. are fast enough to create the efect of actual strobe light at this frequency which is about 11 Hz. What you need for this project is: - 120 K resistor. - 8 K resistor.

https://www.ledsupply.com/blog/12v-24v-leds-making-diy-lighting-easier-than-ever/
The Duo comes in a 12" long piece, sitting at .95" wide. The modular strip design allows you to cut it into smaller sections. Every 3" there is a black dotted line where you can cut it to make multiple LED light engines from one piece. When cutting the strip yourself, be careful to cut along the dotted line.

https://www.instructables.com/Disco-Lights-With-Arduino/
Step 3: Wiring the LED's With the Arduino. Now you can connect the resistors with the Arduino using the jumper cables. First thing I always do is connecting the ground. I used 2 jumper for that, I connected the first end of the jumper to the anodes of the LED's and the other end to the other rail of the breadboard.

https://electronics.stackexchange.com/questions/1487/how-to-build-disco-lights
Otherwise you would have to take a look at frequency analysis, whereby the lights could be triggered by the audio level at different frequency bands (one per light). This system would closest resemble a disco light that flashes with the different instruments in an audio track, but it's much harder to implement when compared to amplitude analysis.

https://www.youtube.com/watch?v=Ym5V9IMuWLc
Make a fantastic party light for your birthday party or event. Perfect for a Disco too! Watch our easy DIY tutorial on how to make a Disco Ball Party Light

https://www.makeuseof.com/stunning-led-diy-projects/
With a bit of creativity, you can use them to add sparkle to any party. From the beer pong table to LED drink coasters, here is a list of stunning LED DIY projects to light up your next party. 1. Interactive LED Beer Pong Table. A classic beer pong game is the perfect way to top up a great party.

https://www.youtube.com/watch?v=D3AbxAJLUws
In this video, we are going to show you making a LED Strobe light using only 12 volt. You can make this circuit at home easily. You also can use this circuit

https://www.instructables.com/LED-Cloud-Light/
To make your cloud portable & free standing, you can build a frame out of PVC pipe. You will need:-seven lengths of PVC pipe: two the same length for the sides (~4ft), four the same length for the base (~1ft), one for the top bar (~3.5ft)-two joints-two tees We used 1" pipe and spray painted it silver. Assemble pieces as shown to create frame.

https://www.lovelyetc.com/diy-light-fixtures/
These 23 DIY light fixtures are incredibly beautiful and most are very easy and inexpensive to make. From chandeliers to pendants and everything in between, there's a beautiful light here for every type of space. When we moved into our 1970s fixer-upper, all of the light fixtures were either incredibly outdated or super basic.

https://www.youtube.com/watch?v=ZccT5AK11Vg
To make it easy if anyone is interested in building one of these strips, I'll put links below for what I used in this video. LED LIGHT STRIPhttps://amzn.to/3

https://www.youtube.com/watch?v=chbCyfsm8ro
Today I will show you how to make a disco light using tin cans and old lamps. Don't forget to visit my channel for more how-to project ideas.

https://www.youtube.com/watch?v=pw3WD7ik43o
A 12 volt LED, easy to adapt for lights. Best I found were at http://rover.ebay.com/rover/1/711-53200-19255-/1?icep_ff3=2&pub=5575119394&toolid=10001&campid