https://www.youtube.com/watch?v=dgM0sFQtl58
Installation guide for Garolite/G10 Build plate for Bambu Lab X1C and P1P. Wipe with IPA before use. Use default High Temp Plate profile.

https://forum.bambulab.com/t/super-simple-diy-garolite-g10-build-plate-for-x1c/54851
Then I adhered adhered the G10 build plate directly to the heated bed using 5 small strips of foil tape. Now for the good news: Based on the previous experience, I planned to pre-heat the garolite at 90C for a half hour before starting a test print. However, I checked its temperature after 10 minutes, and it was already reading surprisingly

https://forum.bambulab.com/t/super-simple-diy-garolite-g10-build-plate-for-x1c/54851/39
Worthy of note: From the X1C control panel you can disable the checking of the build plate. I did, and now I don't get any annoying errors about it complaining the expected build plate isn't there, especially since the knock-off build plate didn't have any of the 2d markers on it.

https://lightyeardirect.com/pages/bambu-g10-installation-guide
Secure payment. Installation Guide Step 1: Remove the build plate from the packaging. Set aside the foil tape. (FOIL TAPE IS ONLY REQUIRED FOR USERS WITH THE STAINLESS STEEL NOZZLE - Bambu P1P and P1S) Step 2: With Scissors, cut a piece of foil tape that is roughly the length and width of the nozzle wipe tab at the top. Peel off adhes.

https://forum.bambulab.com/t/super-simple-diy-garolite-g10-build-plate-for-x1c/54851?page=3
I definitely need to upgrade the X1C lighting before I run into trouble. I received my Lightspeed garolite build plates today. This will speed things up considerably, because now I can remove a build plate as soon as the print finishes and put in a fresh plate, ready to start printing right away. Edit: now printing to the white Lightspeed plate.

https://www.reddit.com/r/BambuLab/comments/xifu77/update_on_g10_as_print_surface_for_x1/
Pay special attention to the rounded corners. (Optional but I find it helps with adhesion and scanning) Use the 400 grit sand paper on the surface of the G10. Start with even up and down passes across the whole surface, then side to side, finally diagonal. Wipe the surface of the sheet with IPA and a lint free wipe to remove all the dust and oils.

https://www.reddit.com/r/BambuLab/comments/wn8y9z/garolite_g10_build_plate_for_bambu_x1_carbon/
Additionally we might want to try sanding/scuffing garolite with 2000 grit sandpaper to reduce any weird reflections that might screw up the lidar. I would imagine a matte surface similar to the cool plate's appearance could cause less issues than a highly reflective glass-like surface that G10 often comes with. Reply.

https://www.reddit.com/r/BambuLab/comments/15qvyso/g10_garolite_plate_is_amazing/
G10 Garolite plate is amazing. I am curious if it is any different to the smooth high-temp Bambu plate, as your description is what I achieve daily with it. On the weekend i tried one of the garolite plates for my X1c. Fantastic smooth finish for a technical piece (an adapter for alternative IKEA Metod Kitchen legs but using exsisting holes).

https://www.youtube.com/watch?v=4AiqDv2Uwdk
Instagram: https://www.instagram.com/thomaslightleFacebook: https://www.facebook.com/redbarnwoodworking/Twitter: https://twitter.com/tnlightle

https://www.youtube.com/watch?v=nv6ELyJ4alg
Testing 7 different build plates for the Bambu Lab X1C.Support the channel and buy a shirt:http://www.lendizzleprintz.com/https://www.patreon.com/LenDizzlePr

https://wiki.bambulab.com/en/filament-acc/acc/plates
Bambu Cool Plate consists of two parts: the Cool Plate sheet and the Engineering Plate. You can print on both sides of the plate. The cool plate sheet, made of PC, has a smooth surface. It's attached to the engineering plate using 3M high heat-resistant double-sided tape. This plate is specifically designed for printing PLA filament.

https://lightyeardirect.com/products/magnetic-garolite-g-10-composite-build-plate-for-bambulab-x1c-and-p1p
Lightyear G10 Build Plate for Bambulab X1C, P1S, and P1P. Sale price $44.99 Regular price $49.99 (/) ... We use a cold-rolled sheet of stainless steel to magnetize the G-10 build plate, making swapping surfaces easy ... The Lightyear G10 will also counter any warping that comes with the stock Bambu beds. Our build plate comes fully assembled

https://www.themakersphere.com/bambu-x1c-upgrades/
Here we will be discussing all of the Bambu X1C upgrades for the printer itself. Aside from the PEI plate, everything on this list can be downloaded and printed for free. Any additional parts will be highlighted so you know exactly what you'll need. The first of many Bambu Lab X1 Carbon upgrades is a PEI build plate. 1. PEI Build Plate

https://support.sliceengineering.com/portal/en/kb/articles/mako-bambulab-upgrade-kit-installation-instructions
Upgrade your Bambu Lab Printer with the Slice Engineering Mako Hotend using our detailed installation guide. Learn what tools you need, step-by-step instructions for removing the old hotend, and how to install the new components. ... Bambu Lab P1P; Bambu Lab P1S; Bambu Lab X1; Bambu Lab X1C; Bambu Lab X1E; What You Need. 2 mm Hex Key. Mako For

https://forum.bambulab.com/t/lightyear-3d-magnetic-build-plates-for-bambu-lab-printers/19344
PREORDER- Ships Early January - Lightyear G10 Build Plate for Bambulab X1C,... Unlock new possibilities with our high-quality Garolite Sheet designed for 3D printing. Elevate your creations with Garolite G10 Sheet, compatible with Lightyear 3D technology. Price: USD 44.99. I printed a 100x100x5mm square. Two of them side by side.

https://www.reddit.com/r/BambuLab/comments/16pv1on/recommendation_for_x1c_build_plate/
With the latest firmware the X1 can now save the flow stuff. Use the plate that came with it and calibrate the K, either by you looking at lines or the lidar looking at a pattern, and save that in the printer. Then calibrate flow, again either you look at stuff or the lidar looks at stuff, and save it in studio.

https://wiki.bambulab.com/en/p1/manual/intro-p1p
The Bambu Lab P1P uses a CoreXY motion system controlled by two stepper motors. The X and Y stepper motors work together to move the print head. P1S share the same motion system. Every stepper motor has an independent belt connected to the print head, so a pair of belts control its position. A CoreXY motion system allows the P1P to print much

https://www.facebook.com/groups/bambulabs/permalink/1061707308174019/
Anyone have the Lightyear G10 Garolite build plate? Preferred settings for PLA on X1C? Also any solution for X1C error saying it can't scan build plate?

https://www.youtube.com/watch?v=Rwf8j4_PVQM
Got myself a new build plate for @BambuLab printers. Lightyear G10 build plate. Unboxing and first test print.

https://www.reddit.com/r/BambuLab/comments/172lrjx/garolite_g10_build_plate_from_lightyear_is_awesome/
To hit the recommended temps from lightyear, the G10 plate works pretty much identical to the smooth PEI hot plate for PLA and PLA+, but with less flex. PETG is a pain. It adheres too well to the cool plate with windex, glue stick, liquid glue, etc. You can make it work, but it radically reduces the lifespan of the cool plate sticker.

https://www.reddit.com/r/BambuLab/comments/1d96noi/recommend_the_g10_build_plate_to_beginners/
G10 pros: Great adhesion. Smooth first layer. Automatic build plate detection. Super easy release once cooled. Probably the easiest for a novice to 3d printing. -- No glue stick, minimal cleaning, great adhesion, easy release. G10 cons (ish): It's best if you wait a few minutes for it to cool below 50 degrees or lower.

https://www.seevid.ir/fa/w/dgM0sFQtl58
Installation guide for Garolite/G10 Build plate for Bambu Lab X1C and P1P. Wipe with IPA before use. Use default High Temp Plate... Installation guide for Garolite/G10 Build plate for Bambu Lab X1C and P1P. Wipe with IPA before use. Use default High Temp Plate profile. ادامه

https://www.reddit.com/r/BambuLab/comments/143hnl2/first_batch_of_garolite_build_plates_sold_out/
First Batch of Garolite Build Plates Sold Out, Next Batch Ships by 7/1. Hello all, you bought too many G10 build plates. Fortunately they will be back in stock by 7/1. Everyone who placed an order prior to 9AM PST on June 7th will have their plate shipped by 6/15. We know, but we aren't trying to compete with the AliExpress stuff.