https://www.youtube.com/watch?v=aUTHbArkPu0
Setting a post is the foundational step for many projects, including building a fence or a deck. ... including building a fence or a deck. Learn how to dig post holes and set 4x4 posts with gravel

https://www.bobvila.com/articles/setting-fence-posts/
Pack the concrete to a level slightly above the surrounding soil. Here, to prevent pooling, trowel the concrete so that it slopes away from the post. Double-check that the post hasn't fallen out

https://www.lowes.com/n/how-to/setting-a-post-with-concrete
How Deep Should I Set a Metal Fence Post? The same standard applies to metal fence posts. Set your metal fence post in a hole that's 1/3 to 1/2 the height of your post but verify the specifics with your local building department. Use a fast-setting mix for convenience when fencing with concrete posts.

https://www.bobvila.com/articles/installing-fence-posts/
Tamp down the gravel using the bottom of the fence post. To do this, set the post in the hole and, with gloved hands, lift the post up a few inches and bring it back down hard on the gravel

https://www.quikrete.com/athome/video-setting-posts.asp
Dig post hole so diameter of the hole is 3 times the width of the post (i.e., the hole for a 4" wood post should be about 12 inches wide). The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet). Step 2

https://www.youtube.com/watch?v=Hu-c2ZjOgwU
Fence posts are the backbone of a fence, so it's crucial to set them properly. In this video, we'll show you how to dig post holes and how to set fence posts

https://www.homedepot.ca/en/home/ideas-how-to/fencing/how-to-install-set-fence-posts.html
After setting the fence posts in concrete, install braces to support them while the concrete cures. These braces can be made from scrap wood and should extend from the ground to the top of the posts at a diagonal angle. Allow the concrete to cure undisturbed for at least 24 to 48 hours, or as recommended by the concrete manufacturer.

https://www.youtube.com/watch?v=UXkvUePo3os
Today we are going to be installing some fence posts! I'm going to be using a new product I've never used before to set the fence post for our horizontal fen

https://www.thisoldhouse.com/fences/21363130/fence-post-installation
How to Install a Fence Post in 5 Steps. Begin by digging the post holes with a shovel or posthole digger. Space holes between 6 to 8 feet on center and, for most picket or lattice fences, dig them 24 to 30 inches deep. Set posts on a 6-inch base of ¾-inch crushed stone to encourage drainage. Then fill around posts with the soil from the holes

https://diy.dunnlumber.com/projects/how-to-set-a-fence-post
To set the posts straight, have a level, some boards, and stakes on hand to brace the post in place if needed. We used a post level, but a regular level can work just fine, too. Step 5: Set posts in place. There are a few ways to set a fence post with concrete.

https://www.familyhandyman.com/project/how-to-set-fence-posts-that-won-t-rot/
Insert Aggregate. Once you've dug your hole, place about 6 inches of aggregate in the bottom of the posthole to allow for drainage. This will minimize the amount of water that comes into contact with your cedar fence post. Pro Tip: The bottom of the post should extend a few inches into the aggregate as shown. Step 4.

https://blog.redbrand.com/how-to-set-fence-posts/
As a general rule, fence posts should be 8 to 12 feet apart and placed at least two feet deep or one-third of the total post height, with a base of soil, gravel, or concrete. Let's take a closer look at how to set fence posts for a strong, sturdy fence. Preparation. Setting fence posts requires some digging.

https://www.quikrete.com/settingposts/
1. Dig the post hole, making it three times the width of the post and at a depth equal to 1/3 to 1⁄2 of the above-ground length of the post, plus 6" (right). For loose or sandy soil, using a tube form is recommended (left). 2. Pour 6" of gravel or crushed stone into the bottom of the hole. Compact and level the gravel using a post or 2 x 4.

https://www.woodmagazine.com/woodworking-tips/techniques/home-improvements/installing-deck-fencing-posts
Dig an 8"-diameter hole at least 6" deeper than your area's frost line for each 4x4 post, using a power auger, hand auger, or post-hole digger. A 6x6 post requires a 10"-diameter hole. Shovel a 6" layer of gravel into the hole to provide drainage. Now, put the strings back on the batterboards, but move them toward the outside of the layout by

https://diy.stackexchange.com/questions/66434/deck-posts-set-in-concrete-or-use-anchors
I build decks for a living. Setting your post in concrete as you would a fence post will work just fine, as long as you use Sono tubes or The Post Collar. You want no earth to wood contact! Or use pier blocks. In the pic you have a ledger securing the deck to the house. You can use 6" pier blocks.

https://todayshomeowner.com/concrete/video/setting-posts-in-concrete-the-easy-way/
Dig the hole. Make it three times the width of the post and one-third to a half the length of the post. Then pour 6 inches of Quikrete All-Purpose Gravel into the bottom of the hole. 2. Put the post in the hole. Level the post and fill the hole with Quikrete Fast-Setting Concrete Mix within 3 to 4 inches from the top of the hole. 3.

https://backyardables.com/top-3-ways-to-set-a-post-without-concrete/
These two-by-fours will stabilize the post. Put a layer of dirt into the hole. Use a two-by-four to push down and compact the dirt, so it becomes more sturdy in the hole. Attach the level to the post and check to make sure that the post is level with the ground. Repeat step 4 until you have filled up the hole to the top.

https://www.youtube.com/watch?v=GEaazdWUiLk
Learn about setting posts the right way for a fence or other structure using fast-setting concrete. ... Learn about setting posts the right way for a fence or other structure using fast-setting

https://howtobuildit.org/the-stress-free-way-to-set-posts-without-concrete/
Step One. Determine where you want your post to go. Use your shovel to remove the dirt and the rocks from the dig site, placing the dirt from the hole onto the tarp. Make sure that you dig at least 2 feet deep for a 7 foot tall post (use this to determine your dig height based on your post). It's also a good idea to double the size of the

https://www.weekand.com/home-garden/article/set-deck-posts-sand-18028124.php
Mix your concrete with water in the wheelbarrow per the directions on the bag. Use the bucket to measure water. Thoroughly mix the concrete with your shovel. Shovel enough concrete in the hole to set a base of 12 inches. Insert the post and, with the help of another person, pump the post up and down slightly to settle the post.

https://www.quikrete.com/athome/settingposts.asp
Setting Posts in Concrete. 1. Dig the post hole, making it three times the width of the post and at a depth equal to 1/3 to 1⁄2 of the above-ground length of the post, plus 6" (right). For loose or sandy soil, using a tube form is recommended (left). 2. Pour 6" of gravel or crushed stone into the bottom of the hole. Compact and level the gravel using a post or 2 x 4.

https://diy.stackexchange.com/questions/176957/how-exactly-do-you-set-these-post-holders-into-concrete
Do you push them all the way down? Or should you leave a gap underneath? If you leave a gap, how big a gap should you leave? It has drain holes on the bottom, which makes me think it needs to be off the concrete, but then you have the full weight of you 6x6 post on that one piece of steel.

https://www.msn.com/en-us/money/other/should-you-use-expanding-foam-for-fence-posts/ar-AA11mY3B
Expanding Foam vs. Concrete for Setting Fence Posts. Post-setting foam is a two-part product, and the parts have to be mixed before use. ... The company sells a similar product for deck posts

https://www.msn.com/en-us/lifestyle/home-and-garden/how-to-pour-footings-for-a-solid-frost-proof-deck/ar-BB1i8Psr
Even if you're setting deck posts in the ground, instead of on top of footings, the concrete still needs to extend below the frost line. FH01DJA_02177002-solid-frost-proof-concrete-footings

https://www.youtube.com/watch?v=qnIigpa7WSA
How to concrete in a post. How to install a post in concrete is a very easy job. It doesn't matter if it's a fence post, a letterbox post or even a basketbal

https://www.msn.com/en-us/money/realestate/how-to-frame-a-deck-a-guide-to-building-a-sturdy-foundation/ar-BB1ieoRm
Set the Posts: Cut your deck posts based on the desired deck height and level the posts in your footings. I always reach for my handy post level at this stage, but you can also use a carpenter's

https://www.amazon.com/VOLISUN-Outdoor-Brightness-Setting-Powered/dp/B0BMWPD3N5
VOLISUN Solar Post Cap Lights Outdoor 4Pack, with Edison LED Bulbs, 2 Brightness Setting, Fence Post Lights Solar Powered for Garden Fence Deck Mailbox Yard Porch, Fits 4x4 6x6 Posts(Slate Black) Visit the VOLISUN Store. 4.6 4.6 out of 5 stars 515 ratings | Search this page .