https://www.youtube.com/watch?v=-I3n9Tq1Bls
How to apply a concrete sealer to new and old concrete! This is what will be going over in this video! So Protect your concrete from stains and get it sealed

https://www.bobvila.com/articles/how-to-seal-concrete/
Force the sealant deeply into the joint. Take care not to leave gaps along the edges, but don't use so much that the sealant forms a bead above the surface of the concrete. After applying the

https://www.lowes.com/n/how-to/howto-seal-concrete
Remove Old Sealer. Step 1: Test for Sealer. ... Let it dry for at least 24 hours before applying the new concrete floor sealer. Apply the Sealer. If you're covering a large surface, a sprayer is a quicker and easier way to apply concrete sealer. For smaller areas, use a paint roller on an extension pole. Follow the steps below to apply the sealer.

https://www.thecleverhomeowner.com/how-to-apply-concrete-sealer/
Step #2: Remove Paint, Grease and Stains. Next, you need to remove materials that can not be removed with a broom of shop vac. This will include grease, paints, and stains that may be present. The products that you will need to use will depend upon the type of material that you seek to clean up.

https://www.concretenetwork.com/concrete/maintaining/sealingplain.htm
Strip any existing sealer from the surface. Open up the concrete with an etching solution. Apply a thin coat of sealer using a roller or sprayer. Wait for the first layer of sealer to dry. Apply a second coat in the opposite direction. Allow the sealer to fully dry before walking or driving on your concrete.

https://www.wikihow.com/Seal-Concrete
2. Sweep or brush the concrete to remove dirt and debris. Take a broom or a stiff brush and give the concrete a thorough sweeping to remove large particles from the surface. Be sure to hit the corners and any nooks and crannies as well. If there are any cracks, sweep out any dirt that may be lodged in them.

https://gambrick.com/how-to-seal-concrete-like-a-pro/
Acid etching is a great way to get rid of the old sealer and it's very easy to do. Dilute some muriatic acid in water and spray it onto the concrete. Let it sit for a minute or two and then scrub it off with a brush. Finally, rinse the acid off and allow the concrete to dry completely.

https://www.thisoldhouse.com/driveways/21327263/sealcoating-driveway
Step 1: Prep your driveway. As a general rule, the night before sealcoating the driveway, position sealer cans lid-down. This enables the solids in the blend to move through the can, making the sealer easier to mix just before application. To mix the sealer, use a corded drill with a paddle, like you'd use to mix thinset for tile or joint

https://www.youtube.com/watch?v=r4JL8elRpZQ
#EverythingAboutConcrete #MikeDayConcreteThis video will show you how to seal a concrete driveway using LastiSeal Penetrating concrete sealer and Tomahawk's

https://www.angi.com/articles/how-to-seal-concrete.htm
Clean the concrete surface with a power washer or chemical cleanser to remove oil, stains, dirt, and previously applied sealer. Old penetrating sealer removal may require chemical etching. Fill in cracks, if necessary. Etch the surface with etching acid by carefully following the product's instructions.

https://www.northeastdecorativeconcrete.com/blog/can-i-apply-concrete-sealer-over-old-sealer
Steps in Applying Concrete Sealer Over Old Sealant. Prepare the surface. Clean the surface. Remove the old acrylic sealer (if necessary). You can use a pressure washer with a mild detergent solution or a pneumatic tool with an abrasive pad to remove old sealants from concrete, stone, and masonry surfaces before applying the fresh coat of exterior concrete sealer.

https://www.youtube.com/watch?v=XtXopmXJ3mo
Applying Concrete Sealer | Part 3 - Sealing ConcreteVisit us at http://toolboxdiy.comApplying a penetrating concrete sealer is a super easy DIY task. It's so

https://www.lowes.com/n/how-to/clean-and-seal-a-concrete-driveway
Garden/Tank Sprayer: Add the sealer to the sprayer's tank. Thoroughly cover the concrete with overlapping strokes. Try not to let the sealer build up anywhere. If you do get buildup, remove the excess with a rag. Complete the first coat and let it dry. Roller and Brush: Apply the sealer just as you'd paint a wall.

https://www.wikihow.com/Seal-Concrete-Floors
Dip the paintbrush into the sealer. Run it along the edges of the first quarter you're painting, where your rolling brush or paint pad may not be able to reach. Use nice, even strokes to apply the sealer. [20] 6. Paint the sealer on the concrete with a paint pad or rolling brush. Pour the sealer into a painting tray.

https://sealwithease.com/how-to-apply-concrete-sealer-on-a-driveway/
Here is a step-by-step guide on how to prepare and apply the concrete sealer: Mixing Concrete Sealant: Most liquid or acrylic concrete sealants come ready to use, but some types may require thinning with water prior to application. Begin by reading all directions on the product label for specific mixing instructions, then combine the necessary

https://mybackyardlife.com/when-to-seal-concrete-patio/
A newly-poured concrete slab needs at least 28 days to cure before you can safely seal it. As for an old concrete patio, you can use a sealer after pressure-washing it with soap and water and letting it dry thoroughly. ... dry surface before you can apply the concrete sealer, so that means waiting at least 28 days until a new concrete pour

https://www.everything-about-concrete.com/concrete-sealer.html
Applying a concrete sealer to new or old concrete is definitely a good idea. Curing and sealing the concrete will help protect it and enhance the concrete's appearance for many years to come. But, knowing which type of sealer to choose for your specific application can be a little challenging.

https://yourgarageguide.com/apply-sealer-concrete/
Apply Sealer Concrete with a Roller. 1. Pour the sealer on a pan. Start off by pouring the sealer on a pan. Place the pan on a surface that is flat. Place the roller cover on the handle of the roller and then get rid of any wrapping. For the best outcomes, you are advised to invest in high-end covers. 2.

https://sealwithease.com/how-long-should-you-wait-to-put-sealer-on-new-concrete/
The concrete, however, needs to be fully cured before you put on a sealer. Almost all sealers require the new concrete to be fully cured before sealing, and this can take up to 28 days. Cure & Seal, on the other hand, is a sealer intended for concrete that has been in place within 2-28 days. Sealing your concrete is essential.

https://www.concretenetwork.com/products-sealer/frequently-asked-questions.html
High-performance topical coatings, such as epoxies and urethanes, will cost more -- typically $0.50 to $2.50 per square foot. In most cases, the investment in a sealer is well worth the expense, when you consider that the cost to replace concrete is generally $7 to $8 per square foot.

https://www.brickform.com/blog/tips-for-sealing-stamped-concrete/
Applying Sealer to Stamped Concrete What you'll need. Before you begin sealing your stamped concrete, here's a list of the supplies you'll need: Concrete sealer (you can choose between water-based or solvent-based) Concrete cleaner, degreaser or etcher; Pressure washer or garden hose; Stiff-bristle brush; Roller or sprayer for applying

https://rulinghomes.com/how-to-apply-concrete-sealer/
Open up the concrete with an engraving solution. Apply a skinny coat of sealer using a roller or sprayer. Wait for the first layer of sealer to dry. Apply a second coat in the other way. Allow the sealer to dry before walking or driving on your concrete completely. While many householders plan to seal their concrete, it is often trickier than

https://cemstone.com/concrete-sealing-protecting-your-investment-from-damage/
Penetrating Sealers Penetrating sealers create a barrier on the concrete. These sealers saturate and absorb into the surface providing lasting protection against moisture and deicing chemicals. These recommended penetrating sealers are breathable, and result in a non-yellowing, natural finish. Easy to apply with a sprayer and a roller.

https://qa15.behr.com/consumer/products/floor-coatings-sealers-and-prep/concrete-floor-sealers/behr-premium-color-enhancing-sealer
Application. DO NOT THIN. Stir or mix product thoroughly before and occasionally during application. Use product when air and surface temperature is between 50-90° F (10-32° C). Apply using a high quality pump sprayer, 1/4" - 3/8" nap roller, synthetic brush, or a sponge pad applicator until saturated.

https://www.a1concrete.com/concrete-repair-learning-center/pouring-new-concrete
Step 7: Cure and Seal the Concrete. The final step involves curing and sealing the concrete. Sealing should be done as soon as the concrete is poured and finished to help prevent cracking and discoloration. The concrete is then left to cure, during which time it gains strength and durability. Curing Time. The curing will continue for several days.

https://www.msn.com/en-us/lifestyle/home-and-garden/renew-your-concrete-patio-how-to-stain-concrete/ar-BB1osFvF
Scrub the concrete with a stiff broom to remove dirt. Then, rinse the entire patio with water. Now, clean the entire surface with a heavy-duty cleaner, working in 4 x 4-foot sections at a time

https://www.youtube.com/watch?v=obEuSo7qAro
#SealStampedConcrete #Reseal Stamped Concrete #MikeDayConcreteIn this video I'm going to share with you how to seal and reseal stamped concrete. I'll show yo

https://www.yelp.com/biz/seal-smart-springfield
The product is from Canada where it was originally applied to huge concrete bridges. Seal Smart first cleans the surfaces (wood, concrete & masonry) to like new with their eco friendly cleaners and orbital power washers, then they apply the product which maintains clean, 'as new' wood grain look.