ImmersiveAmbientModecolor: #e88d5c (color 1)
Video Format : 22 (720p) openh264 ( https://github.com/cisco/openh264) mp4a.40.2 | 44100Hz
Audio Format: Opus - Normalized audio
PokeTubeEncryptID: 09fd66da0f7514af8183882f5089b919c768dfeede208d32864f5d2dd91e8f4c4657d1660530aede3e5d36c30bb6ab52
Proxy : eu-proxy.poketube.fun - refresh the page to change the proxy location
Date : 1715795118450 - unknown on Apple WebKit
Mystery text : b3czRmY2MVJWMkkgaSAgbG92ICB1IGV1LXByb3h5LnBva2V0dWJlLmZ1bg==
143 : true
74,896 Views ⢠May 24, 2021 ⢠Click to toggle off description
đ Want to know the Next Video Topic? Consider supporting the channel for awesome Perks: đ
Patreon Page: www.patreon.com/rcexplained
đď¸ Ordering from Amazon? Use this Affiliate Link to support the channel: đď¸
amzn.to/2QTNjHL
đCheck out these Cool Shirts!đ
www.radiocontrolinfo.com/shop/rcexplained-tees/
Cogging Explained - It may not be what you think:
   â˘Â Brushless Motor Cogging Explained â M... Â
How to improve Cogging/Start up Hesitation in your RC
   â˘Â How to Improve Cogging or Start Up He... Â
High vs Low Motor Timing Applications
   â˘Â Applications of High and Low Brushles... Â
#RCexplained
Views : 74,896
Genre: Science & Technology
Date of upload: May 24, 2021 ^^
Rating : 4.774 (46/769 LTDR)
RYD date created : 2022-04-07T14:41:28.917138Z
See in json
YouTube Comments - 73 Comments
Top Comments of this video!! :3
I had damaged lead (wire) from the ecs to motor and got this behavior. Good call.
5 |
Thanks.
I just got a second hand set up. I think I got this scenario. I have a capacitor on the esc that got hot quickly. I probably tried it 3 times on the throttle on the bench for about 15-30 seconds. Is that enough to damage the esc/motor please?
4 |
Totally had a bad bullet connection between my esc and outrunner motor! Simple fix! Thanks!
2 |
thank u ! mine has similar problem..now it was fixed...simple as that...
2 |
I'm here because I searched YouTube for 'noisy brushless motor' in an attempt to figure out why my wood stove's blower motor was making a noise sounding like the blades were hitting the metal sides. I already knew the rheostat (speed controller) was faulty, but had no idea IT could be the cause of the extra noises. Thanks for making this video. I'll replace the rheostat and keep the motor/blades.
5 |
Great short tip ryan
2 |
Literally saved my day. Thanks bro.
1 |
thank you man.. you saved my esc.
|
Hey I have a problem with my sensored motor in my touring car. it works like it should most of the time, it can slowly start up without cogging and so on. But if I pull the car backwards and slowly get on the throttle, it shouts out backwards even if there is sensors and everything to prevent this happening. Do you think something is wrong or is this normal???
|
G'day mate again thanks for your help and advice đ đ Peter
1 |
Thanks. Big helpâŚ
|
Thanks so much
|
Omg, thank you! It's so obvious now. I didn't solder them at all yet. 4082+150a are just heat shrinked together for initial testing. Ok... Time to solder
|
My Sidewinder ESC started cogging and I traced it to the plugs. Cleaned it, ran it for a bit fine, then every time it flipped over or came to a stop, it started cogging. I never had any issues like this before. Iâm thinking I need to try a more durable ESC.
1 |
Thank you đ¤ was able to detect my issue
|
Thanks for the video! I am experiencing cogging almost identical to what your video showed. However, all the leads are properly soldered and connected and it's still cogging. Can't even get the rotor a full rotation. Bearings and rotor are all good. Do you have any suggestions?
5 |
Thanks!
1 |
Is this the same solution when the motor can spin(I have a BLiTZ SCT) but when on the ground it will just vibrate?
|
how if after run.. at long distance motor cogging, it is reciever or esc setting
|
@tankdavies800
2 years ago
This happened to me and I had an esc failure then I saw this video very helpful thanks
9 |