PokeVideoPlayer v23.9-app.js-020924_
0143ab93_videojs8_1563605_YT_2d24ba15 licensed under gpl3-or-later
ImmersiveAmbientModecolor: #d1aa86 (color 2)
Video Format : (720p) openh264 ( https://github.com/cisco/openh264) mp4a.40.2 | 44100Hz
Audio Format: 140 ( High )
PokeEncryptID: 1492a5b0bf720c5ff687c5a7427965b4f78d21ac0aedaafe3440644f0ad61d3304dcca52e6790bc0e70a76beffbcad23
Proxy : eu-proxy.poketube.fun - refresh the page to change the proxy location
Date : 1740030029359 - unknown on Apple WebKit
Mystery text : WDh6N09LTE84NEkgaSAgbG92ICB1IGV1LXByb3h5LnBva2V0dWJlLmZ1bg==
143 : true
112,335 Views โข Oct 6, 2024 โข Click to toggle off description
Views : 112,335
Genre: Howto & Style
License: Standard YouTube License
Uploaded At Oct 6, 2024 ^^
warning: returnyoutubedislikes may not be accurate, this is just an estiment ehe :3
Rating : 4.893 (125/4,533 LTDR)
97.32% of the users lieked the video!!
2.68% of the users dislieked the video!!
User score: 95.98- Overwhelmingly Positive
RYD date created : 2024-11-03T11:04:53.924038Z
See in json
71 Comments
Top Comments of this video!! :3
Great save ๐ป
67 |
Those carbs are super simple. Needle and seat, float, one jet, that's it. Problem is, it's a brass jet screwed into an aluminum housing. Ethanol in gas absorbs water, and voila - jet never unscrews again due to galvanic corrosion. Well, it does with a lotta heat...
33 |
I have cleaned dozens of carbs of varnish and other crud. Carb cleaner spray, a thin copper wire to poke out the holes, and a air compressor to blow out the holes works great. The only carb I could not clean out and make work was a plastic carb on a lawnboy mower. Ugh. When I shut down any engine for the winter, I empty the gas tank and run the engine until it runs out of gas. That way varnish will not accumulate in the carb as the gas evaporates. Big oh yeah, use no alcohol gas in your small engines.
|
If it doesn't start after you checked like the main 2 things (has gas and can flow to the engine) and does the spark plug spark, then it's always the carb. I just take it apart and soak it in original pinesol for a day, since I don't have an ultra sonic cleaner. Just don't put the plastic float in it. Rinse it all off, spray it down with carb cleaner then assemble. everything be peachy.
2 |
I wish I was as knowledgeable as you. Thatโs awesome, love your vids.
3 |
I do this ALL the time.
1) Either
2) It doesn't start. Spark plug/ignition.
3) starts n stalls. Fuel issue (95% of the time. Gas is junk. Use marine/aviation fuel & sea foam if stored with gas.)
If 3 then 4) put sea foam in gas. Make sure it gets into carb (loosen float bowl. Wait a day.
5) still won't start, clean float bowl (see 4) and "carb cleaner" jets with straw.
6) really dirty carb. Yank it, pull float bowl, yeet it in sonic cleaner for several cycles till like new. No need to disassemble.
Works 99% of the time.
If Gen runs but no power out... look up "flashing the armature." Ask and I will describe. NEVER RUN A GENERATOR WITHOUT A LOAD!
Have fun... oh and don't use your tong to check for voltage.
1 |
Same here. If I have a small engine that will not start, even with good gas and spark, check on price of new carb. Have two year old Echo weedeater that would not start so checked on new carb. $12. No brainer, ordered and installed new carb. Ditto on DeWalt generator. But. . . New carb = $330. No brainer, cleaned old carb three times. Finally got it going.
|
Take the pin holding the float and clean the needle, use a torch tip cleaning tool to clean the jets. Works about 75% of the time
|
You deserve recognition brother
|
Can't tell you how many great tools I've been given because they don't work. Several because they were out of gas. Most was just a little bit of maintenance that was never done.
9 |
I have done this several times to get the jet out of a carburetor flat head impact bit but u just need to grinds the side of the bit to fit into the small hole and might have to shave the thickness depending on bit used
|
Anthony!!! Can you make a video talking about the new refrigeratants and the new air conditioners what your thoughts are on them???????
2 |
Great ๐ ๐ Job!!! ๐
๐ฏ ๐
๐ฏ ๐
๐ฏ
2 |
Thereโs nothing this guy canโt fix, rebuild, repair, correct, or coerce into working again.
Iโd like to work with you.
2 |
I use ether, but will look into sea foam!
Nice one!
|
I'm a little lazier, i start with spraying something into the carb to get it to run. Not a lot but i want to verify it's a fuel issue before i move on. I never bothered with a spark tester, but I should get an inline tester eventually. Not high priority because I've only had that come back and bite me once. A bad spark plug. I could never figure out why that happened on a newish Honda engine that was used.
|
man is there anything you canโt fix ๐
5 |
Sea foam is beautiful
|
You don't need to rebuild the carburetor. Just add some FTC decarbonizer to the fuel. 1hr with decarbonizer and your good as new.
|
@redhauscreator146
4 months ago
When it comes to carburetors the best you can do is rebuild or get a new one. Good job.
98 |