PokeVideoPlayer v23.9-app.js-020924_
0143ab93_videojs8_1563605 licensed under gpl3-or-later
ImmersiveAmbientModecolor: #cc998a (color 2)
Video Format : (720p) openh264 ( https://github.com/cisco/openh264) mp4a.40.2 | 44100Hz
Audio Format: 140 ( High )
PokeEncryptID: f1fadec3eacfdc5fcebf573d044e070bc72d7ae9e69495063dfde2a5014d2a1aa6f2aada87492873e56e15a934baa697
Proxy : eu-proxy.poketube.fun - refresh the page to change the proxy location
Date : 1730262641219 - unknown on Apple WebKit
Mystery text : MWp5bU4zQkVuN1kgaSAgbG92ICB1IGV1LXByb3h5LnBva2V0dWJlLmZ1bg==
143 : true
105,430 Views โข Feb 23, 2023 โข Click to toggle off description
Here's how to use a multimeter to test if the circuit of the car heating system has a pulse signal:
Turn off the car and let the engine cool down before beginning the testing process.
Locate the wiring diagram for the car heating system to identify the wires that carry the pulse signal.
Set the multimeter to the voltage setting.
Connect the black probe of the multimeter to a good ground point in the engine compartment.
Connect the red probe of the multimeter to the wire that carries the pulse signal.
Start the engine and let it idle.
Observe the multimeter reading. If the reading fluctuates between 0 and 12 volts, then the circuit has a pulse signal.
If the reading is steady at 0 volts or 12 volts, then the circuit does not have a pulse signal and there may be an issue with the component that generates the pulse signal.
Check the wiring and connectors for any signs of damage or corrosion.
If the wiring and connectors appear to be in good condition, then further diagnosis may be necessary to determine the cause of the issue.
Views : 105,430
Genre: Autos & Vehicles
License: Standard YouTube License
Uploaded At Feb 23, 2023 ^^
warning: returnyoutubedislikes may not be accurate, this is just an estiment ehe :3
Rating : 4.99 (3/1,227 LTDR)
99.76% of the users lieked the video!!
0.24% of the users dislieked the video!!
User score: 99.64- Masterpiece Video
RYD date created : 2024-07-25T16:55:09.252452Z
See in json
11 Comments
Top Comments of this video!! :3
Thanks for the great information
2 |
Thanks ๐
|
So if it doesn't do this or it only does it when I move the wire does that mean a short in the wire somewhere? Or if it doesn't do it at all does that mean it's bad?
|
I need a calibration tutorial for the Duoyi DY518. I have two devices that are out of calibration because the 4 buttons were accidentally pressed simultaneously and the message "rst sys" appeared on the display, disconfiguring the devices.
1 |
Did you turn the car on?
1 |
is there one of these to help urgent
electrical professor
electrician
electric technician
my case :
( when i connect the multimeter red to red the + / and black probs ) . gives reading as continuity
important notes :
1 - NO BATTERY
2 - multimeter ON Diode mode " continuity"
- is that normal - ?!?!?!
1 |
Or just the first power
1 |
Sonthst mesns its bad ?
1 |
Some kindergarten level of mm understanding here
1 |
Last time I did it this way my battery was fried
1 |
@TheDoodla
9 months ago
This is so helpful. Thanks so much ๐
3 |