11:08
Automobile Door Weatherstrip Installation - C2 Corvette
19:40
Adding a third brake light to a 63-66 C2 Corvette .... pretty slick!
24:10
C2 Corvette fender flare removal.... going back to stock.... from start to final paint.
06:22
Route 66 Cruise to Bibo, NM
19:34
1973 Datsun 240Z - walk around and drive
03:12
How to check a Fuel Sending Unit to see if it Works!
24:38
How to build an automotive Exhaust System from scratch!
15:06
Shorten a Driveshaft in your Home Garage
05:53
Torque Converter Installation and More - Make Sure it is Right for your Application
10:20
Early Chevy LS1 Engine Valley Cover Replacement ... removing the boss
09:32
Installing the Holley 302-3 / 302-5 Oil Pan on a Chevy LS Engine
04:21
Chevy LS Engine Rear Main Seal Replacement
03:46
Chevy LS Engine Oil Galley Plug (Dumbbell - Dog Bone) Replacement
06:41
Borgeson Pressure Reducing Kit for Power Steering Pump - Installation
19:21
Swapping an LS1 Engine/4L60E Transmission into a 1966 C2 Corvette Chassis
25:01
Datsun 280Z Engine Rebuild Part 3 of 3 - Finish Assembly and Start Up
08:42
Installing Pistons on the Connecting Rods and Putting the Rings on the Pistons
13:40
Datsun 280Z Engine Rebuild Part 2 of 3 - Building the Short Block
07:07
Datsun 280Z Engine Rebuild Part 1 of 3 - Disassembly and Inspection
14:01
1966 C2 Corvette RideTech Rear Suspension Installation
24:41
1966 C2 Corvette Differential Rebuild Part 2 - Assembly
08:29
1966 C2 Corvette Differential Rebuild Part 1 - Disassembly
20:57
1966 C2 Corvette Rear Wheel Hub Rebuild Part 2 - Assembly
08:56
1966 C2 Corvette Rear Wheel Hub Rebuild Part 1 - Disassembly
20:58
1966 C2 Corvette Front Suspension Installation, Borgeson, Wilwood, RideTech. Part 2 of 2
26:24
1966 C2 Corvette RideTech Front Suspension installation. Part 1 of 2
09:36
1966 C2 Corvette Chassis Disassembly, clean, paint, and make removable transmission cross-member.
06:30
How to remove headlight doors/ buckets from C2 Corvette
11:38
1966 C2 Corvette project - Removing body from frame
06:35
If you need Windshield Wiper Arms for your Datsun 240Z, 260Z, or early 280Z, watch this video.
18:01
1970 Datsun 240Z V8 gets an exterior update.
11:43
1970 Datsun 240Z V8 Interior Makeover
15:15
Frenching Taillights and License Plate... anybody can do it. I show you how to french in this video.
08:31
Refinishing Recaro Leather Bucket Seats with Rub N Restore https://rubnrestore.com?rnr=32303
20:11
How to install Wilwood mechanical parking brake calipers.
19:48
Wilwood Brake Caliper Rebuild. The brakes on this 1970 Datsun 240Z V8 get redone.
08:34
1970 Datsun 240Z V8 gets new Clutch Master Cylinder and Slave Cylinder.
00:09
Great Ball of Fire ... carburetor backfire
15:24
1970 Datsun 240Z V8 ... getting it running
14:34
How to install a Lokar Throttle Cable ... see all the steps!
09:46
Mallory Electric Fuel Pump disassembly, inspection, cleaning, reassembly, and testing.
14:26
1973 Datsun 240Z Final assembly - finishing touches of the restoration
04:20
Datsun 240Z clutch pedal slop / play / loosness repaired.
12:06
Datsun 240Z Carpet Installation plus rust repair and sound deadening
14:53
Classic Car Windshield Installation - How to do it - Datsun 240Z
03:53
Dash Cover Installation. How to Install a dash cover on a Datsun 240Z.
12:39
1973 Datsun 240Z Glove Box Fabrication
11:50
1973 Datsun 240Z Door Latch Repair and more
04:23
Painting / Dyeing Automotive upholstery fabric with Tulip brand upholstery spray. Datsun 240Z
12:53
1973 Datsun 240Z Engine Bay Detailing
14:31
Datsun 240Z - Triple Weber Carburetors - Cold Air Intake Box - Air Cleaner Fabrication
26:57
Datsun 240Z Heater Core Replacement with one from a Mazda Pickup. New temperature control valve too!
04:50
1973 Datsun 240Z Build Update - ready for paint
07:33
1973 Datsun 240Z Rust Repair on the Body
23:11
1973 Datsun 240Z Complete Brake Job
08:31
1973 Datsun 240Z Clutch master cylinder and slave cylinder replacement.
02:15
Weber DCOE 40 Air/Fuel Idle Mixture Screw Adjustment
10:35
1973 Datsun 240Z Runs after many years of outside storage.
03:49
1973 Datsun 240Z Electrical System Check
35:50
Weber DCOE 40 Carburetor Rebuilding
X
About
This channel is for the purpose of sharing some of my projects with others and potentially helping them with their own projects. Hopefully, some of my videos will be entertaining as well. Thank you for subscribing to my channel. I have had an interest in the automobile since I was about 6 years old. I once made a living as an engine rebuilder for a local Automotive Machine Shop. In my younger days, I raced the dirt tracks of the Southwest in Sprint Cars, Modifieds, and Stock Cars. Now I pretty much just restore, rebuild, and customize cars, trucks, and motorcycles of all makes. I like everything automotive, including gas station memorabilia. I have always done my own fabrication including mechanical, paint & body, and upholstery. It is just a hobby that gives me great satisfaction. I do not have a business and I am not for hire.
Tags