00:51

Rubber bands to pull the nasty bits away

06:04

Part 41 (Making the motherboard)

30:16

Part 40 (Aligning X axis ball screw)

20:31

Part 39 (Adjusting front gibs on the table)

08:47

Part 38 (Finally time to put the table back where it belongs!)

06:40

Part 37 (Adjusting the gibs under the saddle)

15:57

Part 36 - (Time for lube!)

16:01

Part 35 - (Homing, sweet homing!!!)

47:47

Part 34 - (Looking at the electronics)

07:56

Using the end mill as an indexing stop to locate your stock

20:27

Part 33 - (Levelling the machine)

30:58

Part 32 - (It's alive!!!)

17:44

Part 31 - (Installing the Y axis ball screw)

19:28

Part 30 - (A justing the center gibs on the saddle)

18:53

Part 29 - (Trimming the turcite)

15:42

Part 28 - (FADAL project update)

19:19

Part 27 - (New angular contact bearings for Y axis ballscew)

20:28

Part 26 - (Brand new way lube for the saddle)

07:37

Part 25 - (Metering valve values for the saddle lubrication)

09:40

Part 24 - (Repacking X axis ball screw)

13:08

Part 23 - (Repacking Y axis ball nut)

17:48

Part 22 - (Looking at the Y axis Ball Screw assembly)

07:37

Part 21 - (Introduction to the 3D model of the machine)

03:06

Part 20 - (Installing the tool changer casting)

01:59

Part 19 - (Inspecting the underside of the table)

09:56

Part 18 - (Painting)

01:13

Part 17 - (What's that?)

04:30

Part 16 - (Removing the spindle 2 of 2)

18:22

Part 15 - (Removing the spindle 1 of 2)

04:18

Part 14 - (Removing the spindle pulley)

13:30

Part 13 - (Removing the draw bar)

11:00

Part 12 - (Draw bar cylinder)

05:05

Part 11- (Degreasing, cleaning, buffing, scrubbing)

03:17

Part 10 - (Metering valves values for the Z axis)

04:23

Part 9 - (Inspecting the backside of the Z axis)

03:32

Part 8 - (Looking at the spindle motor mount)

06:07

Part 7 - (Inspecting the underside of the Y axis)

04:22

Part 5 - (Cleaning and inspecting the Z gibs)

14:51

Part 6 - (Removing way lube on Y axis)

02:44

Part 4 - (Removing Z axis)

06:07

Part 3 - (Removing the spindle motor)

06:29

Part 2 - Fadal VMC 4020 CNC (Removing the tool changer Casting)

04:39

Part 1 - Fadal VMC 4020 CNC reconditioning

08:01

Followup on live stream with Brad Talis

01:41

Runout filament sensor

00:59

Phoque à Tartigou

02:54

Grand héron bleu

02:27

Voile au Lac Towago

02:22

Voile au lac Towago

00:33

Ver éventail à identifier

00:45

Poisson d'eau douce à identifier

00:20

Espèce à identifier

00:43

Ver non identifié

00:19

Espèce de concombre de mer inconnu

00:48

Nudibranche inconnu

02:37

Les Ilets aux Méchins (Bas St-Laurent, Québec)

00:14

lévitation

06:46

Ces Voix Oubliées 2007

04:03

Images sous-marines du St-Laurent