10:01

Computer Input and Output Circuits ( high and low side drivers, pull up and pull down circuits)

09:59

Using the Picoscope and Serial Decoding to Analyze CAN Bus Data

02:23

Testing Resistance on the CAN Bus Network

10:06

Testing Variable Valve Timing Operation by Looking at Cam and Crank Signals (Picoscope)

05:28

Looking at Cam and Crank Position Signals to Verify Timing (Good Test For Variable Valve Timing Too)

06:50

Using Data Logging to Analyze Volumetric Efficiency

13:20

Using Data Logging to Analyze Data for Mass Airflow, Fuel Trims, and Lambda Sensors

02:20

Setting Up the OBDLink MX+ for Data Logging

01:10

Example of a Bad In Cylinder Pressure Waveform (2014 Honda Pilot Lack of Power-Backpressure)

21:30

Diagnosing Engine Performance Issues Using an In Cylinder Pressure Transducer (Detailed Analysis)

09:57

Using the Picoscope NVH to Diagnose a Vibration (2004 Ford Expedition)

13:16

Diagnosing a Misfire 2006 Ford F150 5.4L Using the Crank Sensor and Picoscope Math Channels

07:19

How to Set Up Your NVH Toolkit and Software (OBDLink MX+ as Passthrough)

12:43

Looking at Current Draw of DC Motors Using a Picoscope (2010 Malibu Power Windows)

03:37

CAN Bus Diagnostics 3 (shorts and opens on module with no termination resistor) 2007 Toyota Camry

06:56

CAN Bus Diagnostics 2 (Opens and Shorts) 2007 Toyota Camry Using the Picoscope

13:09

Diagnosing CAN Bus Networks with Picoscope (Shorts and Opens) On A 2013 Ford Fiesta

04:47

Testing for Poor A/C Performance/ Air Not Blowing Cold Enough/ How to Test a Relay

02:38

Diagnosing Bad O2 Sensors, Lean Codes, Random Misfire 2002 Chevy 6.0L

02:00

P0300 Random Misfire Code, Using the Picoscope with a Pressure Transducer

04:32

Fun Prank!!! How To Wire Someone’s Horn To Their Blinkers.

10:55

Turning a Brake Rotor On a Brake Lathe

08:30

Turning a Brake Drum On a Brake Lathe

02:22

How to calibrate a micrometer

05:54

How to measure a brake drum using a brake drum micrometer.

03:15

How to measure brake rotor thickness and thickness variation.

04:09

How to bench bleed a brake master cylinder.

07:10

How to cut, bend, and flare brake lines.

01:25

How to properly torque lug nuts.

04:03

How to use a 2 post symmetrical lift to raise a car.

06:27

How to use a 2 post asymmetrical lift to raise a car.

03:10

How to use a 4 post lift to raise a car.

03:31

How to set and use a torque wrench.

14:28

How to Perform a Full Wheel Bearing Service Including Repacking and Adjusting

02:33

How to Adjust Wheel Bearings. How to Set Wheel Bearing Preload.

08:08

How an Alternator Works. Using a Picoscope to Graph 3 Phase Current

01:29

1997 GMC 5.7L with O2 Sensor Codes Using a Scan Tool to Monitor 02 Data

01:29

Testing a Mass Airflow Sensor MAF on a 2013 GMC Sierra 5.3L

01:18

Measuring Rotor Runout to Check for Warped Brake Rotors

02:31

How to Use a Ridge Reamer to Remove the Ridge at the Top of the Cylinder

02:10

Honing a Cylinder

04:15

How to Install a Piston Using a Piston Ring Compressor

03:26

How to Use Plastigage to Verify Bearing Oil Clearances

03:05

Torquing Cylinder Head Bolts

02:40

Measuring Valve Stem Installed Height

00:54

How to Remove Valves from a Head

01:19

Measuring Camshaft Lobe Lift

00:29

Measuring Camshaft Runout

05:57

Measuring Cylinder Bore Diameter, Out of Round, and Taper

01:35

How to Replace a Headlight Bulb

00:44

Measuring Piston Ring End Gap

02:30

Removing Camshaft Bearings

00:54

How to Remove Freeze Plugs

00:50

Measuring Crankshaft Runout

00:32

Measuring Piston Ring Side Clearance

00:29

Measuring Connecting Rod Side Clearance

00:50

Measuring Piston to Deck Height Clearance

00:37

Measuring Crankshaft End-Play

02:31

Can You Diagnose a Restricted Exhaust Using the MAP Sensor

03:50

How to Remove a Harmonic Balancer