08:23

13 How to pickup TRACE sample address from ladder screen 08 00

06:36

02 How to understand each soft key 06 30

10:00

03 How to set trace setting 10 00

05:24

04 How to download trace result 05 300

02:33

01 How to access TRACE screen 03 00

09:09

05 How to use softkey on trace screen 09 00

07:39

06 How to use softkey on trace setting screen 07 30

09:17

07 How to set TRACE parameter for Sample 09 00

09:32

08 How to set TRACE parameter for Stop condtion 09 00

09:52

09 How to set TRACE parameter for Sampling condtion 09 00

06:46

10 How to read TRACE parameter from io device 06 00

03:20

How to shift home position (example DVF 500 Y-axis)

01:42

How to access P- code variable

01:08

How to access AWC I/O status screen

02:48

How to EIP setting backup & Restore

00:19

How different Travel measure with Analog + Digital indicator

01:38

How to upload Messages file

00:07

How to access ATC Guidance screen (PW: 1111, VTR-series)

07:43

18 How to use diagnsis display 7 00

04:14

19 How to report to us when you got alarm after changing Motor or Drive 4 00

05:24

20 How to upgrade firmware software if necessary 5 00

04:50

11 How to check VPF signal on status + cabinet + doosandrive 4 00

08:46

12 How to distinguish spec of motor and Drive 8 00

03:25

12 1 How to set teaching pos 3 30

09:18

13 How to distinguish teaching pos control and pot pos control 9 00

05:39

15 How to distinguish new encoder type 5 30

05:27

17 How to undersand TM Automatic operation 5 00

09:06

16 How to understand TX servo drive 9 00

04:19

14 How to use Jog Run function 4 00

03:04

03 How to check input main power compact +old type 3 00

01:58

02 1 How to check battery 3 6V AA 2 00

06:00

02 How to replace battery 3 6V AA 6 00

04:32

09 How to reset home 5 00

07:19

10 How to check Position signal from CNC form Vision 7 00

01:52

08 How to change parameter 2 00

03:09

How to initialize all parameters (Vision Drive , TX경우는 각각의 Path에서 초기화를 해야함)

03:18

06 How to check IO cable compact+old type 5 00

05:45

05 How to check motor power cable compact+old type 5 00

05:19

04 How to check motor encoder cable compact+old type 5 00

02:38

03 1 How to check input main power circuit breaker primary secondary 3 00

09:35

01 How to service Promotion Motor and Drive 10 00

04:45

00 Doosan Servo Histoy 4 50

00:13

How to understand ATC action (VCF850, with Chip pan and ATC door)

01:07

How to check Mega Ohom (spindle) = Display 1 means Max Mega Ohm at this equipment.

00:05

Where is blinking DOT (TX drive, 2nd axis)

03:33

How to update CUFOS software

00:26

SMX EOP(EZWORK) menu tree around April 2019

01:40

How to access Ethernet IP_for Scanner (15 inch screen, DVF5000, AWC)

01:53

How to check VTS head tool memory (Tool table + D71 bit)

01:00

DNM4500 EOP(EZWORK) menu tree around April 2016

02:25

How to download P-code values

00:48

How to check and set main program (@ mark_when Rengui does not work properly)

02:24

How to do all data backup from CUFOS

01:05

How to recovery from stuck in the booting middle (Oif Plus)

00:41

How to find Part No. for Doosan Drive's Hosing and Contact

00:41

How to recovery Matrix (alarm 2403)

01:42

How to understand Sub changer and Waiting tool pot (DHF 8000)

01:04

How to understand ATC Time chart sticker (CAM 곡선)

01:42

Introduction_DBM 2540 AAC (Auto Attachment Changer)

01:01

How to find Part No. for Sol. cable with plugs attached.